Motors
!

Vibrating Motor
35-160
!
100-Up $.99, 1000-Up $.85, 10K-Up $.65
 

7/8" x 3/8" x 1/4"
1.3 volt, 80 mA
Vibration caused by the offset
weighted shaft.  Originally intended
for pagers, cell phones or vibrating
batteries.  1-1/2" leads with mini 2-pin
connector.

24 VDC Variable Reluctance Stepping Motor
35-118
!

 

Mfg. - SINGER
1-1/2" dia. x 1-1/2" body
1-1/2" shaft, 1/8" dia. shaft
24 VDC, 71 ohm coils
Step angle 15 Degrees -
7.5 Degrees halfstep

2 Speed Vibrating Motor With Switch
35-165
!
 

3 VDC (1.5 - 6 VDC)
1-7/8" x 1" x 13/16"
Motor 1.35" x .94" x .72"
Shaft .07" (2mm) dia x .4" long
Vibration caused by the offset
weighted shaft. 3-position slide
switch (off/slow/fast). Elements
will fit size "AA" or "AAA" cells.

 

24VDC SOLENOID
80-319
!
 

Mfg. - GUARDIAN
Mfg.# - A420-066859-00
1-13/16" x 1" x 1-3/16"
24 VDC, 35 ohm coil
Type # 11 boxframe
Pull @ 1/8 45oz
Holding force 92 oz
.187" quick connect contacts
0-3/4" stroke length

Elite 801 Air Pump
35-166
!

Mfg. - ELITE
Mfg. # - 6150
Size: (approx)  4.25"(W) x 2.50" (L) x 2.12" (H)
Very good for small pressure projects, or a great
aquarium air pump. Comes already wired with a
standard AC cord. There is a plastic hose nipple
on the side that takes a 1/8" I.D. tube.

120 VAC Fan Motor
35-162
!
 

Mfg. - OH SUNG
Mfg. # - F960112-2
2-7/8" x 1-1/2" x 2-1/2"
3/4" shaft
120V, 60Hz

This impedance protected fan motor is most
commonly used in refridgerators, vent fans,
battery chargers, amplifiers etc.

6VDC 3500 RPM Motor
35-168
!
 

Mfg. - JOHNSC.
Mfg. # - HC970
Body: 2" dia x 3" long
Shaft: 1/4" dia x 15/16" long
This reversible motor is rated at 6VDC
@ 2 am, no load speed 3500 RPM. Shaft
end mounted with two 8 x 32 tapped holes.
Copper brushes for long life.

UDN2931W Motor Drive
UDN2931W
!
 

Mfg. - ALLEGRO
3 Channel half-bridge
motor driver
2 amp continuous output current
15V output sustaining voltage
Internal clamp diodes
Low output saturation voltage
Internal thermal shutdown circuitry
Housed marked

1 HP Motor Treadmill Duty
35-167
!
 

Mfg. - GENERAL ELECTRIC
Mfg # - 5KH40HT43D
5"sq x 5-1/2" deep, 13 lbs
115VAC, 60 Hz @ 11 amp - no load, 60 cycle,
1725 RPM, rotation CCW, bushing bearings.
Square open frame motor with 2-1/8" rubber
shock mounts. Shaft size: 3-1/4" L x 1/2" dia
with flat key-way. Input 1/4" quick connect
terminals # 2 & 5.