Motors

Vibrating Motor
100-Up $.99, 1000-Up $.85, 10K-Up $.65

7/8" x 3/8" x 1/4"
1.3 volt, 80 mA
Vibration caused by the offset
weighted shaft. Originally intended
for pagers, cell phones or vibrating
batteries. 1-1/2" leads with mini 2-pin
connector.

35-160

High Torque Mini Motor

Mfg. # - FF-N20PN
11/16" x 7/16" x 3/8"
1-1/2 to 3 VDC
No load: 15,800 RPM @ 2.4
VDC, 96 mA. For use in small
applications when size is limited
Solder terminals.

35-163

12-24 VDC Motor
100-Up $.60, 1000-Up $.49

Mfg. - NISSEI DENKI
Mfg. # - 7C20
Body: 1.20" x .785"
Shaft: .058" x .236"
No load speed 25000 RPM
@ 8mA at 24 VDC.

35-164

24 VDC Variable Reluctance Stepping Motor

Mfg. - SINGER
1-1/2" dia. x 1-1/2" body
1-1/2" shaft, 1/8" dia. shaft
24 VDC, 71 ohm coils
Step angle 15 Degrees -
7.5 Degrees halfstep

35-118

2 Speed Vibrating Motor With Switch
100-Up $.85 TEMP OUT

3 VDC (1.5 - 6 VDC)
1-7/8" x 1" x 13/16"
Motor 1.35" x .94" x .72"
Shaft .07" (2mm) dia x .4" long
Vibration caused by the offset
weighted shaft. 3-position slide
switch (off/slow/fast). Elements
will fit size "AA" or "AAA" cells.

35-165

24VDC SOLENOID

Mfg. - GUARDIAN
Mfg.# - A420-066859-00
1-13/16" x 1" x 1-3/16"
24 VDC, 35 ohm coil
Type # 11 boxframe
Pull @ 1/8 45oz
Holding force 92 oz
.187" quick connect contacts
0-3/4" stroke length

80-319

Air Pump

Mfg. - ELITE
Mfg. # - 6150
Size: (approx) 4.25"(W) x 2.50" (L) x 2.12" (H)
Very good for small pressure projects, or a great
aquarium air pump. Comes already wired with a
standard AC cord. There is a plastic hose nipple
on the side that takes a 1/8" I.D. tube.

35-166

120 VAC Fan Motor

Mfg. - OH SUNG
Mfg. # - F960112-2
2-7/8" x 1-1/2" x 2-1/2"
3/4" shaft
120V, 60Hz

This impedance protected fan motor is most
commonly used in refridgerators, vent fans,
battery chargers, amplifiers etc.

35-162

6VDC 3500 RPM Motor

Mfg. - JOHNSC.
Mfg. # - HC970
Body: 2" dia x 3" long
Shaft: 1/4" dia x 15/16" long
This reversible motor is rated at 6VDC
@ 2 am, no load speed 3500 RPM. Shaft
end mounted with two 8 x 32 tapped holes.
Copper brushes for long life.

35-168

UDN2931W Motor Drive

Mfg. - ALLEGRO
3 Channel half-bridge
motor driver
2 amp continuous output current
15V output sustaining voltage
Internal clamp diodes
Low output saturation voltage
Internal thermal shutdown circuitry
Housed marked

UDN2931W

1 HP Motor Treadmill Duty

Mfg. - GENERAL ELECTRIC
Mfg # - 5KH40HT43D
5"sq x 5-1/2" deep, 13 lbs
115VAC, 60 Hz @ 8 amp - no load, 60 cycle,
1750 RPM, rotation CCW, bushing bearings.
Square open frame motor with 2-1/8" rubber
shock mounts. Shaft size: 3-1/4" L x 1/2" dia
with flat key-way. Input 1/4" quick connect
terminals # 2 & 5.

35-167